Best Printable Vinyl & Chrome Films for Mimaki CJV300 Plus (2026 Buyer's Guide)
Printable Vinyl & Specialty Films Compatible with Mimaki CJV300 Plus
The Mimaki CJV300 Plus is a workhorse 54-inch and 64-inch eco-solvent print/cut machine running Mimaki's SS21 inkset (or BS3 / SS21 NCC depending on configuration). It's the most common Mimaki in US sign shops, sticker producers and fleet wrap studios. This page covers the Graphictac films our team has tested on the CJV300 Plus, plus the recommended profiles, ink density and lamination guidance.
If you run a CJV300 Plus and want to evaluate our films before placing a roll order, request our Free Pro Sample Pack — 12 trimmed swatches shipped from our Cypress, CA warehouse, configured for SS21 eco-solvent inks.
Why CJV300 Plus owners ask about media compatibility
The CJV300 Plus uses Mimaki SS21 (or BS3) eco-solvent ink. Two practical considerations for media selection:
- SS21 lays slightly drier than Roland TR2. This means our films generally accept higher ink density without bleed. Our recommended values below are 10–15% higher than the equivalent Roland VG3 settings.
- Cut sensor reads matte and gloss reliably; chrome and holographic need pre-laminate. Same convention as Roland — apply 3mil matte laminate to mirror films before contour cut on the CJV300 Plus.
Recommended Graphictac Films for the Mimaki CJV300 Plus
1. 6mil Semi-Rigid Printable Permanent Matte White Vinyl (20in / 30in / 54in)
- Suggested ink density: 290–310% (10% higher than Roland eco-solvent)
- Print heater: 40 °C (Mimaki's pre/print/post heater split — aim 40 on print)
- Pass: 8-pass High Quality for solid colors; 6-pass Standard for outdoor
- Lamination: 3mil overlaminate for >12 month outdoor
2. Optically Clear Removable Printable Commercial Grade (54in x 150ft)
- Suggested ink density: 250–270%
- Print heater: 38 °C
- Recommended white underbase if printing on dark windows
3. Mirror Chrome Printable Vinyl (Gold Bubble-Free 30in / Silver Air-Release 54in)
- Suggested ink density: 230–250% (chrome accepts ink slowly — do not exceed)
- Print heater: 35 °C
- Cut sensor note: 3mil matte laminate required before contour cut on chrome
4. 4mil Rainbow Holographic Stretchable Printable Vinyl (30in x 100ft)
- Suggested ink density: 240–260%
- Print heater: 38 °C
- Lamination: 2mil matte laminate strongly recommended
5. Graphictac 10mil Anti-Curl Roll-Up Banner Media (36in x 100ft)
- Suggested ink density: 270–290%
- Print heater: 42 °C
- Single-sided print only
Profile and RIP Notes
The CJV300 Plus typically runs Mimaki RasterLink RIP. We recommend:
- Start with the closest stock Mimaki SS21 profile
- Adjust total ink limit per the values above
- For shops printing daily volumes >30 sqm/day, request our CJV300-specific ICC profile bundle — free for verified wholesale accounts
Lamination & Finishing
| Application | Recommended Laminate | Why |
|---|---|---|
| Vehicle decals, fleet graphics | 3mil cast gloss overlaminate | UV protection, conformability |
| Window graphics (interior) | 1.5mil clear gloss | Anti-scratch, optional |
| Window graphics (exterior, 12+ months) | 3mil clear gloss with UV inhibitor | Prevents ink fade |
| Floor graphics | Anti-slip 5mil textured laminate | Required for indoor commercial use |
| Chrome and holographic decals | 3mil matte overlaminate | Cut-sensor reliability |
Roll Width Compatibility
The CJV300 Plus accepts media up to 64 inches wide depending on configuration (54in or 64in models). Common widths: 20in, 30in, 36in, 54in. Custom slits available on 6+ roll wholesale orders.
FAQ
Q: Will Graphictac films void my Mimaki CJV300 Plus warranty?
A: No. Mimaki warranty covers hardware and SS21 ink, not third-party media.
Q: How does Graphictac compare to 3M IJ180 / Avery MPI 1105 on the CJV300 Plus?
A: Comparable performance for general signage. Our 6mil semi-rigid and chrome films are typically priced 25–40% below at wholesale tier 1. Side-by-side sample testing welcomed.
Q: Do you offer ICC profiles for the CJV300 Plus?
A: Yes for verified wholesale accounts. Specify "CJV300 Plus SS21" when requesting.
Q: What's the lead time on a sample pack?
A: 2 business days from order to delivery via USPS Priority. Ships from Cypress, CA.
Q: Minimum order quantity for wholesale pricing?
A: Tier 1 starts at 10 rolls per month. Tier 2 at 30+ rolls per month.
Next Step: Test Before You Commit
Request a free sample pack sized for CJV300 Plus print testing — includes 12 swatches, recommended ink density reference card and instant wholesale quote.
Request Your Free Pro Sample Pack →
Or call our wholesale team: (949) 988-0077 — Mon–Fri, 9am–5pm Pacific.
Graphictac USA · 5550 Cerritos Ave, Cypress, CA 90630